当前位置:首页 - 新闻动态 > 公司公告 >

电脑弹簧机显示器厂家的几大问题

来源: http://www.diannaothj.com    时间:2017-03-23 17:38:01 作者:山东银丰弹簧机设备

一、机器提示轴伺服故障,驱动器显示AL 41式Er 7,说明这两个报警信号都为过载。其中三洋伺服为AL41 ,佳宝伺服为Er 7。
First, the machine prompts the axis servo failure, the driver shows AL 41 Er 7, indicating that these two alarm signals are overloaded. The SANYO servo AL41, Jiabao servo for Er 7.
1、机器提示过载报警,先检查相应的轴是否有被异物卡住。例如:X轴报警、查看凸轮滑块处是否有弹簧等异物卡住。Z轴报警,查看转芯是否被螺丝锁住。
1, the machine alarm overload alarm, check whether the corresponding shaft was foreign body stuck. For example: X axis alarm, check whether there is a spring at the cam slider and other foreign bodies stuck. Z axis alarm, to see whether the core is screw lock.
2、如没有被异物卡住,关闭电源、拔了相应驱动器上的接线插头。仔细检查各线是否有松动接触不良。如有重接即可。
2, if there is no foreign body stuck, turn off the power supply, pull out the plug connection on the corresponding driver. Carefully check whether the lines have loose contact. If you can reconnect.
电脑弹簧机
二、系统提示找不到834卡,电脑控制部分是由主电脑板TH834-F0卡与TH834-F1卡组成。它们之间是用插针式接脚连接,出现此故障极有可能是插针接触不良。
Two, the system can not find a 834 card, the computer control part is composed of the main computer board TH834-F0 card and TH834-F1 card. They are connected by a pin type connector, which is likely to be a bad contact pin.
1、打开控制器后盖,首先把各轴控制线I/0输入输出信号线及键盘信号线 除,再打开安装电脑铁盒的盖板。可看到里面从上到下依次安装了TH84-F、TH834-F0电脑主板。
1, open the controller cover, the first axis line of control input and output signals of I/0 line and the signal line in addition to re open the keyboard, the computer box cover. Can be seen from top to bottom in order to install the TH84-F, TH834-F0 computer motherboard.
2、螺丝,把上面两块卡取了。用橡皮擦仔细擦拭每个针脚,去除插脚表面灰尘及被氧化导电性差的表层。然后重新安装(注意:安装时先对准卡四个角的螺丝孔位,然后重新安装(注意:安装时先对准卡的四个角的螺丝孔位 ,然后在无大阻碍的情况下,慢慢将针脚插入插槽内)。
2, screw, the above two cards taken. Wipe each pin carefully with an eraser to remove the dust on the surface of the pin and the surface of the oxide layer which is electrically conductive. And then re install (Note: when installing the first alignment card four corners of the screw holes, and then re install (Note: when installing the first alignment card of the four corners of the screw holes, and then without obstacle situation, slowly pin inserted in the slot).

上一篇:无凸轮弹簧机的使用比其他弹簧机的优势
下一篇:弹簧机在生产的时候图纸审核的内容
联系我们