当前位置:首页 - 新闻动态 > 公司公告 >

查找电脑压簧机风扇转动声音的方法

来源: http://www.diannaothj.com    时间:2016-04-22 09:43:05 作者:山东银丰弹簧机设备

1 发动机的转速有淬火回火钢丝及韧化处理钢,热处理都采用保护气氛热处理,所以地弹簧的调整调节螺丝钉时必须注意用转速表测量转速。保护气氛热处理能够消除表面脱碳和氧化,提高 材料的表面质量。安装转向弹簧时首先应识别做弹簧还是右弹簧,右侧的弹簧应该装在左边,左边的弹簧反之。
The rotation speed of the engine (1) of quenched and tempered steel wire and the toughness of steel processing, heat treatment with protective atmosphere heat treatment, so the adjustment of the spring regulation screws must pay attention with a tachometer speed measurement. Protective atmosphere heat treatment can eliminate surface decarburization and oxidation, improve the surface quality of the material. Should first identify the right or do spring spring is installed on the right side of the steering spring, spring should be installed on the left, on the left side of the spring and vice versa.
2观察风扇叶片上是否沾上灰尘或者风扇外架靠近扇叶的内壁是否有灰尘,如果有灰尘的要去掉。每个风扇都上都有一个圆形标签,把标签撕开(注意不要撕烂了,因为还要贴回去),即可看到一个小的圆形塑料盖,打开塑料盖看,往风扇轴处添加机油,重新复原即可。
2 to observe whether fan blades from dust or fan frame near the inner wall of the blade is the dust, if there is to remove dust. Each fan all have a circular label, the label torn (note don't tore, because also posted on the back), you can see a small circular plastic cover, open the plastic cover, fan shaft to add oil, restoring the can.
3左右弹簧的鉴别方法:用左手握住弹簧,大拇指朝上,其余的手指指向正好与钢丝旋转的方向相同者为左弹簧,反之为右弹簧。调速的弹簧使用后弹力会使柴油机达不到应有的转速,可用调节螺钉进行调整。
3 left and right spring identification method: with the left hand holding the spring, thumb up, the rest of the fingers pointing to the same direction as the direction of the wire with the same person as the left spring, and vice versa for the right spring. Speed adjustment of the spring after the use of the elastic force will not be the engine can not reach the proper speed, can be adjusted by adjusting the screw.
4若是左右的弹簧装错,拖拉机转向时,转向弹簧就会受到反绕向的作用力,是弹簧变形甚至将弹簧折断或者转向齿轮的内台阶削损坏。弹簧折断后手柄放松后,转向齿轮失去了推理的作用后,牙嵌不能回位,可能引发严重的事故。
4 if around spring installed wrong, tractor steering, steering spring will be around to force, is spring deformation even spring break or turn to step in gear cutting damage. Spring break after the handle and relax after the steering gear lost after tooth reasoning, can not return, may cause a serious accident.

上一篇:造成电脑弹簧机系统失控的原因?
下一篇:数控弹簧机的日常三大维护系统
联系我们