当前位置:首页 - 新闻动态 > 公司公告 >

保障电脑弹簧机的日常高效运转的几大注意事项

来源: http://www.diannaothj.com    时间:2016-05-23 15:49:29 作者:山东银丰弹簧机设备

①开机时要严格按照使用步骤及说明进行操作。电脑弹簧机在出厂前必须进行各种检测和调试操作,用户在使用前必须检查调试机器时所要调动的紧固件,以免在生产过程中产生松动、掉落或移位等造成撞机现象,导致弹簧机的机械部分损伤。弹簧机
Boot to be strictly in accordance with the use of steps and instructions for operation. Computer spring machine in the factory must be for all kinds of testing and debugging operation, the user before use must check when the machine commissioning to mobilize the fasteners, in order to avoid in the production process produce loose, falling or shift, caused by the collision phenomenon, resulting in spring machine mechanical damage.
②在长期停机状态下要尽量把送线轮松开。因为弹簧机的送线轮在长时间的压迫作用下,会导致轴承的损伤或送线轮的轻度变形,致使后期开机使用时会造成送线精度不稳定。此外,如果带线压紧时间过长,有可能会使线径产生变形,下次开机使用时会造成异线板卡线或芯棒堵塞等现象,影响其固件的精密性。
In the long run down the state to be as far as possible to release the wire wheel. Because the wire feeding wheel of the spring machine can cause the damage of the bearing or the slight deformation of the wire feeding wheel in the long time, the precision of the wire feeding line is not stable when the late boot is used. In addition, if with pressing time line is too long, it is possible to will make the line diameter deformation, the next boot use will cause different line card line or mandrel blockage phenomenon, affect the precision of the firmware.
③技术师傅要尽量监督技术人员的调试过程。学徒在调机时,师傅要尽量在现场,以减少或避免不必要的事故发生。此外,学徒调试好产品后,师傅一定要进行检查。
The technical master should try to supervise the technical personnel's debugging process. Apprentice in the transfer machine, the master should try to be in the field, to reduce or avoid unnecessary accidents. In addition, the apprentice after the commissioning of a good product, the master must be checked.
④机器在运转过程中,禁止触碰弹簧机的工作面板。电脑弹簧机在运转过程中,禁止我们用手去接触弹簧机面板,以免机器构件的运转对我们造成伤害。
The machine in the process of operation, the working panel no touching spring machine. Computer spring machine in the process of operation, we prohibit the use of hand contact with the spring board, in order to avoid the operation of the machine components of our damage.
⑤要控制好加工产品的掉落方向。弹簧机产品的自由掉落一定要控制好方向,否则将会卡住刀座等部件,引发不必要的撞刀或撞机现象。
The direction to fall control processing products. The free fall of the spring machine products must be controlled in a good direction, otherwise it will jam the knife seat and other parts, causing unnecessary collision knife or hit the machine.
⑥修整产品时,一定要进行停机操作。在数控弹簧机日常工作中,如发现产品出现异样,一定要停止操作后才能进行调整修正,避免发生意外事故。
The dressing products, must stop operation. In the daily work of CNC spring machine, such as the product found strange, be sure to stop after the operation to adjust the correction, to avoid accidents.
⑦电脑弹簧机出现故障时,请专业人员进行检修。弹簧机出现损坏或故障时,要由有经验或专业人员进行检查和修正;报修时,由相关的专业人员进行维修。严禁无专业技术人员进行擅自拆卸,以免发生二次损坏。
The computer spring machine malfunction, please professional personnel for maintenance. When damage or malfunction occurs in the spring machine, by experience or professional personnel for inspection and correction; repair, by the relevant professional personnel for maintenance. No professional and technical personnel to carry out unauthorized demolition, so as to avoid the occurrence of the two damage.

上一篇:数控弹簧机的装机流程
下一篇:复式压缩机的弹簧固定结构原理
联系我们