当前位置:首页 - 解决方案 >

电脑弹簧机的弹簧表面油漆处理方法

来源: http://www.diannaothj.com    时间:2019-04-18 12:58:12 作者:山东银丰弹簧机设备

1.喷涂法  喷涂是应用喷枪将油漆喷成雾状微小颗粒在弹簧外表上平均堆积一层漆膜。施工便当,而且漆膜厚薄比拟平整、润滑。但喷涂法对油漆的有效应用率仅70%-80%左右,同时比其他办法需求更多的溶剂,这些溶剂又将全部挥发而损耗太大。另外,由于油漆雾粒扩散洋溢及溶剂的挥发,形成环境污染,影响工人安康。
1. Spraying spraying is the application of spraying gun to spray paint into foggy particles on the surface of springs to accumulate an average layer of paint film. The construction is convenient, and the thickness of the paint film is smooth and lubricated. However, the effective application rate of spraying method to paint is only about 70% - 80%. At the same time, more solvents are needed than other methods. These solvents will all volatilize and consume too much. In addition, due to the diffusion and overflow of paint mist particles and volatilization of solvents, environmental pollution is formed and workers'health is affected.
2.其他办法  随着主机构造的变化和弹簧在工作时工况条件的日趋苛刻,为了进步弹簧的运用寿命,如气门弹簧等的外表防蚀处置改为在弹簧清洗后,上特殊防锈油 来替代传统的氧化或镀层处置。
2. In order to improve the service life of springs, the special rust-proof oil is added to replace the traditional oxidation or coating treatment after the springs are cleaned.
电脑弹簧机
3.浸涂法  浸涂法就是将弹簧放人油漆槽中浸渍,然后取出,让外表多余的油漆液自然滴落,经过枯燥后在弹簧外表上被掩盖一层漆膜。浸涂法消费效率高,可适用于机械化、自动化消费,而且技术简单、操作便当。但油漆挥发较快。
3. The dipping method is to put the spring into the paint tank and soak it, then take it out, so that the superfluous paint drops naturally. After drying, it is covered with a layer of paint film on the surface of the spring. The dipping method has high consumption efficiency and can be applied to mechanized and automated consumption. It is also simple in technology and convenient in operation. But the paint volatilizes quickly.
4.静电喷涂法  将热固性粉末经过喷腔口时的一霎时,感应上负电荷,在与紧缩空气的作用下,将塑粉平均地涂敷于弹簧的外表。这些就是它的办法。理解只是一局部,更多的信息还是要本人去发现哦。
4. When the thermosetting powder passes through the nozzle of the spray chamber by electrostatic spraying, the negative charge is induced, and the plastic powder is evenly coated on the surface of the spring under the action of compressed air. These are its ways. Understanding is only part of it. More information should be found by myself.

上一篇:数控弹簧机的装机离不开哪些步骤?
下一篇:数控弹簧机怎么会出现蓝屏的情况呢?
联系我们