当前位置:首页 - 客户服务 >

模具强力压簧机弹簧的生产设计原则特点

来源: http://www.diannaothj.com    时间:2019-07-23 16:49:57 作者:山东银丰弹簧机设备

模具压簧机强力弹簧的特性及设计准绳,从理论上对异形钢丝模具弹簧与圆钢丝弹簧的应力、刚度、变形停止了剖析。简述了模具强力弹簧的设计办法,指出了影响模具强力弹簧开展的主要问题。近年来随着模具工业开展,模具弹簧特别是异形截面钢丝模具弹簧的应用数量和种类日益增大。异形截面模具弹簧具有刚度大、寿命长、体积小等特性。但其设计理论开展比拟缓慢。目前,除正方形截面强力弹簧的设计办法比拟成熟外,其它截面强力弹簧的设计办法,根本是依据详细截面经过实验,找出修正系数得出详细截面的经历设计公式
The characteristics and design criteria of the strong spring of the die spring press have theoretically analyzed the stress, stiffness and deformation of the special-shaped steel wire die spring and the circular steel wire spring. The design method of die force spring is briefly described, and the main problems affecting the development of die force spring are pointed out. In recent years, with the development of die industry, the number and types of application of die springs, especially special section steel wire die springs, are increasing. The special section die spring has the characteristics of large stiffness, long service life and small volume. But its design theory develops slowly. At present, except for the mature design method of the strong spring with square cross-section, the design method of the strong spring with other cross-section is basically based on the experimentation of the detailed cross-section to find out the correction coefficient and obtain the empirical design formula of the detailed cross-section.
压簧机是运用这种弹簧者很关怀也必需搞分明的问题。
Spring press is a problem that people who use this kind of spring care about and must make clear.
下面以正方形截面与圆截面螺旋弹簧作一比拟。在相同空间内,正方形截面钢丝弹簧承载才能比圆截面簧要高43—48%。显而易见,矩形簧要大于50%以上。从运用应力过大是弹簧毁坏的主要缘由剖析,在相同条件下,异形截面钢丝弹簧比圆截面钢丝弹簧的寿命要进步13—14%。异形截面钢丝弹簧能产生大的变形量。异形钢丝弹簧的重量大。线性度比圆截面弹簧好,即刚度更趋于常数值。特别是长边平行于轴线绕制的弹簧。应用范围遭到一定的限制:从剖析可见,异形截面资料弹簧如不能充沛应用其优点,便不会产生经济效益。
The following compares the square cross-section with the circular cross-section coil spring. In the same space, the load-bearing capacity of square section steel wire spring is 43-48% higher than that of circular section spring. Obviously, the rectangular spring is more than 50%. From the point of view that excessive stress is the main cause of spring failure, under the same conditions, the life of special section steel wire spring is 13-14% longer than that of circular section steel wire spring. The special section steel wire spring can produce large deformation. Special-shaped steel wire spring has large weight. The linearity is better than that of circular cross-section spring, that is, the stiffness tends to be constant. Especially the spring whose long side is parallel to the axis. The application scope is limited to a certain extent: from the analysis, it can be seen that if the special-shaped section data spring can not fully apply its advantages, it will not produce economic benefits.
(1)用圆截面资料达不到设计载荷。(2)取代圆截面复合弹簧。(3)用圆资料弹簧达不到所需求变形量的时分。(4)弹簧装置空间小的中央。(5)请求弹簧特性严厉的中央。
(1) The design load can not be reached by using circular section data. (2) Replace the circular cross-section composite spring. (3) When the circular data spring can not reach the required deformation amount. (4) The center of spring device with small space. (5) Request the center with strict spring characteristics.
弹簧机
二、模具弹簧设计准绳
2. Design Criteria of Die Spring
1.弹簧资料许用应力[τ]的选择,应以保证弹簧疲倦寿命为主停止思索。弹簧的动态寿命,普通分为三类:
1. The selection of allowable stress of spring data should be based on ensuring the fatigue life of spring. The dynamic life of springs is generally divided into three categories:
Ⅰ类:接受交变载荷次数为106;Ⅱ类:接受交变载荷次数为10—105;
Category I: the number of times to accept alternating load is 106; Category II: the number to accept alternating load is 10 - 105;
Ⅲ类:接受交变载荷次数小于10?;2.资料宽厚比(a/b)不宜过大,而弹簧的旋绕不宜过小。
Class III: Acceptance of alternating loads less than 10?; 2. Data width-thickness ratio (a/b) should not be too large, and spring winding should not be too small.
3.设计非矩形的异形截面弹簧时,一定要推导和绘制在不同旋转比、不同宽厚比与变形修正系数(τ)和切应力修正系数(β)的曲线或计算公式。4.要依据给定条件和限制条件,选择计算烦琐和参数选择合理的设计办法。
3. When designing non-rectangular spring with special section, it is necessary to derive and draw curves or calculation formulas for different rotation ratios, width-thickness ratios, deformation correction coefficients (_) and shear stress correction coefficients (beta). 4. According to the given conditions and constraints, we should choose the complicated calculation and parameters to choose the reasonable design method.
压簧机三尚存问题1.模具设计规范化水平低,限制了规范化模具弹簧的开展速度。
The three remaining problems of spring press 1. The low level of standardization of die design limits the development speed of standardized die spring.
2.模具弹簧规范化水平低,目前除我所为汽车工业制定的QC7111—7113规范外在国内尚无正式运用的国标或行业规范,模具设计人员无规范可选是急待处理的问题。
2. The standardization level of die springs is low. At present, there is no national standard or industry standard formally applied in China except QC7111-7113 standard for automobile industry. It is an urgent problem for die designers to choose no standard.
3.设计理论不完善,目前比拟成熟的是矩形截面螺旋弹簧,但对其公差选用尚无定论。其异形截面螺旋弹簧均以矩形截面为根底,经实验加以修正。
3. The design theory is not perfect. At present, the comparatively mature coil spring with rectangular cross-section has not yet been decided on its tolerance selection. The helical springs with special cross section are all based on rectangular cross section, which are corrected by experiments.
4.没有异形截面资料消费的定点厂,特别是没有此类资料的油淬火回火钢丝供给厂家。而由弹簧制造厂本人改制的资料,质量不稳定,造价高,影响此类弹簧的推行应用。
4. Fixed-point factories without special section data consumption, especially oil quenching and tempering steel wire suppliers without such data. However, the data restructured by spring manufacturer itself are of unstable quality and high cost, which affects the application of this kind of spring.
5.没有消费此类弹簧的专用卷簧设备。模具用螺旋弹簧旋绕比普通都小于4,而国内卷簧机适用绕制旋绕比在4以上的弹簧。
5. There is no special coiling spring equipment for consuming this kind of spring. The spiral spring winding ratio for die is less than 4, while domestic spring coilers are suitable for winding springs with winding ratio more than 4.
更多的关于弹簧机的问题或者详细的内容,请进入我们公司的网站:http://www.diannaothj.com 网站中会有很多的内容仅供参考。
For more questions or details about spring machines, please go to our website: http://www.diannaothj.com, there will be a lot of content for reference only.

上一篇:无凸轮转线弹簧机可以解决哪些行业痛点?
下一篇:弹簧机屏幕不显示的与什么因素有关?
联系我们