当前位置:首页 - 客户服务 >

弹簧机屏幕不显示的与什么因素有关?

来源: http://www.diannaothj.com    时间:2019-08-14 15:58:08 作者:山东银丰弹簧机设备

弹簧机往常曾经成为一种粗浅的称谓,弹簧不只是原始的那种螺旋的了,呈现了形形色色的外形---行业内称之为线成型机。弹簧机的分类有很多种,也有很多不 同的分法万能弹簧机以满足特殊需求为主的特种弹簧,如纺织机械用摇架弹簧,弹簧机央求有高的抗松弛性能。弹簧机弹簧的伸长量与所受的力的大小成正比。
Spring machine has always been a superficial term. Spring is not only the original spiral, but also presents a variety of shapes - called line forming machine in the industry. There are many kinds of spring machine classifications, and there are also many different kinds of special springs, such as rocker springs for textile machinery, which require high anti-relaxation performance. The spring elongation of the spring machine is proportional to the magnitude of the force it is subjected to.
弹簧机碟形弹簧之外还呈现了气弹簧、橡胶弹簧、涡卷弹簧、模具弹簧、不锈钢弹簧、空气弹簧、记忆合金弹簧等新型弹簧。汽车弹簧、气门弹簧、碟形弹簧、异形弹簧、蜗卷弹簧、恒力弹簧、制动弹簧、冲压件弹簧、离合器弹簧、摩托车减震弹簧、火车减震弹。波簧,扭簧,拉簧。弹簧的品种复杂多样,按外形分,主要有螺旋弹簧、弹簧机涡卷弹簧、板弹簧等。
In addition to the disc spring of spring machine, new springs such as air spring, rubber spring, scroll spring, die spring, stainless steel spring, air spring and memory alloy spring are presented. Automotive spring, valve spring, disc spring, special spring, coil spring, constant force spring, brake spring, stamping spring, clutch spring, motorcycle shock absorber spring, train shock absorber. Wave spring, torsion spring, pull spring. There are many kinds of springs, which can be divided into coil springs, scroll springs and leaf springs according to their shapes.
弹簧机屏幕不显现缘大致为下面四大问题。
Spring machine screen does not appear edge is roughly the following four problems.
1.显现器毛病
1. Display defect
假如以上剖析都不成立,在工作状态下检查显现器右下角电源信号灯的显现状况能否正常,如呈淡黄色或不显现则可能是显现器自身毛病。
If the above analysis is not valid, check the display status of the power supply signal lamp in the lower right corner of the display under the working state, if it is light yellow or not, it may be the display itself.
弹簧机
2.正常范围
2. Normal range
机器正常工作到5分钟忽然中止显现,此为机器正常状况,按键盘上恣意键即可恢复。
When the machine works normally for 5 minutes, it suddenly stops appearing. This is the normal condition of the machine. The random keys on the keyboard can be restored.
3.信号问题
3. Signal problem
显现器上的电源指示灯(绿色)不断闪烁,则检查显现器上信号线接头(插在电控箱第二个槽内的电路板上)能否松动;并察看机箱内底板上的供电插头P8P9旁的 四个红色指示灯能否有正常点亮。如若没有,请将P8.P9两组供电插头取下重新插入,如仍不可用,则检察输出至底板的直流电压(P8.P9上的电压)能否 正常。此两排线上红线为5V,黑线为0V,黄线为12V。如以上均正常,则有可能是显卡损坏。
The power indicator lights (green) on the display continuously flicker, then check whether the signal wire connector (inserted on the circuit board in the second slot of the control box) on the display can be loosened, and check whether the four red indicators beside the power supply plug P8P9 on the bottom of the box can be properly lit. If not, please remove and reinsert P8.P9 two sets of power supply plugs. If it is still not available, check whether the DC voltage output to the bottom (voltage on P8.P9) is normal. The red line is 5V, the black line is 0V, and the yellow line is 12V. If all above are normal, it may be damaged graphics card.
4.电路问题
4. Circuit problems
显现器上的电源指示灯不高,则标明显现器没有正常供电,可用万用表丈量从继电器( OUT-0)输入显现器的电压能否正常。
If the power indicator lamp on the display is not high, it is obvious that the display does not have normal power supply. The voltage of the display input from the relay (OUT-0) can be measured by a multimeter.

上一篇:模具强力压簧机弹簧的生产设计原则特点
下一篇:最后一页
联系我们