当前位置:首页 - 新闻动态 > 企业动态 >

数控弹簧机转动部分的日常的维护特点

来源: http://www.diannaothj.com    时间:2017-04-11 18:47:38 作者:山东银丰弹簧机设备

 一、关闭数控弹簧机电源,等待五分钟让循环机油流回储油槽。找一接油盘,置于润滑泵之下方,缓慢缷下缷油塞,让油流到接油盘里。(注意:不要一下子拿掉缷油塞,以防油从缷油口冲出流到地面。),放置支撑架于储油槽底下。
Turn off the power of the CNC spring machine, wait for five minutes to let the circulating oil return to the oil storage tank. Find a pan, under a lubrication pump unloading, slowly lowering plug, let the oil flow to drip pan. (Note: do not suddenly take off oil plug, to prevent the oil from the oil inlet flow to the ground rushed off. The support frame is placed under the oil storage tank.
二、放松润滑泵固定螺丝,取下润滑泵,松开储油槽上方螺丝,取下储油槽并清洗。在这操作中有以下几点需要注意:
Two, loosen the lubrication pump fixed screw, remove the lubrication pump, loosen the oil tank above the screw, remove the oil tank and clean. In this operation, the following points need to be noted:
1、请将储油槽底下放置同高的支撑架,避免在进行拆装动作时,不慎将润滑泵摔坏等一些意外事故放生。
1, please put the oil tank under the same height of the support frame, in order to avoid disassembly and assembly operations, the pump will be accidentally broken and other accidents.
2、取下润滑泵时,请注意供油马达电源线,请勿做强行拉扯或试图取下线头之动作。
2, take off the lubrication pump, please pay attention to the oil supply motor power cord, do not pull or try to pull the pull off the head of the action.
三、清洗吸油口处过滤网,清除附着在过滤网上的杂质。
Three, clean the oil filter at the mouth of the filter, remove impurities attached to the filter.
四、对回油口处过滤网进行清洗,清除附着在过滤网上的杂质。注意事项有以下几点:
Four, at the back of the oil filter at the mouth of the cleaning, removal of impurities attached to the filter. Note the following points:
1、将机件清洗再加以擦拭,请先确认无异物附着,再行安装操作。
1, the machine cleaning and then wipe, please confirm that no foreign matter attached, and then install the operation.
弹簧机
2、随时注意储油槽油面高度,请勿让油面过低,造成润滑不良。
2, pay attention to the oil tank oil level height, do not let the oil surface is too low, resulting in poor lubrication.
五、打开储油槽加油盖,添加循环机油,让储油槽油面达到MAX位置,盖上并旋紧储油槽加油盖,装上回油管,开机后保持机械运行五分钟,让机器得到充分润滑。
Five, open the gas tank cover, add circulating oil, let oil tank surface to MAX position, on the cover and tighten the oil tank filler cap, with the return pipe, after maintaining mechanical running five minutes, let the machine get sufficient lubrication.
本文文章来源:弹簧机更多的内容请进入: http://www.diannaothj.com我们的官方网站
This article source: spring machine more content please enter: http://www.diannaothj.com our official website

上一篇:凸轮带转线万能弹簧机的使用特性
下一篇:选购无凸轮弹簧机要检查伺服电机好坏
联系我们